P0705 Nissan



Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / P0705 Transmission range sensor A

The 5R05, also called RE5R05A (Nissan part) or JR507E/JR509E (Jatco part), is a Jatco and Nissan Motors 5-speed automatic transmission, released in 2002, used in rear wheel drive or 4X4 vehicles with longitudinal engines. P0725 NISSAN Meaning The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send a.

DTC Logic

DTC DETECTION LOGIC

DTCCONSULT screen terms [Trouble diagnosis content]DTC detection conditionPossible causes
P0705T/M RANGE SENSOR A [Transmission Range Sensor A Circuit (PRNDL Input)]Two or more range signals simultaneously stay ON continuously for 5 seconds under the following diagnosis condition 1 and 2:
  • Diagnosis condition 1 (continued for 5 seconds or more)
  • TCM power supply voltage: More than 11 V
  • Diagnosis condition 2 (continued for 2 seconds or more)
  • Vehicle speed: Less than 3 km/h (2 MPH)
  • Accelerator pedal position: 0.6/8 or less
  • Idle switch: ON
  • Stop lamp switch: ON
  • Harness or connector (Short circuit between transmission range switch and TCM)
  • Transmission range switch

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Start the engine.
  2. Maintain the following conditions.

Accelerator pedal position : 0.0/8

Brake pedal : Depressed

Vehicle speed : 0 km/h (0 MPH)

  1. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for 10 seconds or more.)
  2. Check the first trip DTC.

Is “P0705” detected? YES >> Go to TM-161, 'Diagnosis Procedure'.

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK TCM INPUT SIGNALS

With CONSULT


  1. Turn ignition switch ON.
  2. Select “Data Monitor” in “TRANSMISSION”.
  3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION SW”.
  4. Shift selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item.

Without CONSULT


  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Turn ignition switch ON.
  4. Shift selector lever from “P” to “L” and check voltage between TCM harness connector terminals and ground.

Is the check result normal? YES >> Check intermittent incident. Refer to GI-39, 'Intermittent Incident'.

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power voltage.)]>>GO TO 2.

NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power voltage.)]>>GO TO 4.

NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power voltage.)]>>GO TO 6.

NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power voltage.)]>>GO TO 8.

NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power voltage.)]>>GO TO 10.

2.CHECK D POSITION SW CIRCUIT (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.

Is the check result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts.

3.CHECK D POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.
  2. Turn ignition switch ON.
  3. Check voltage between TCM harness connector terminal and ground.

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

4.CHECK N POSITION SW CIRCUIT (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.

Is the check result normal? YES >> GO TO 5.

NO >> Repair or replace malfunctioning parts.

5.CHECK N POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.
  2. Turn ignition switch ON.
  3. Check voltage between TCM harness connector terminal and ground.

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

6.CHECK R POSITION SW CIRCUIT (PART1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.
P0705 nissan altima

Is the check result normal? YES >> GO TO 7.

NO >> Repair or replace malfunctioning parts.

7.CHECK R POSITION SW CIRCUIT (PART 2)

P0705 Nissan Versa 2014

  1. Disconnect transmission range switch connector
  2. Turn ignition switch ON.
  3. Check voltage between TCM harness connector terminal and ground.

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

8.CHECK P POSITION SW CIRCUIT (PART 1)

  1. Turn ignition switch OFF
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.

Is the check result normal? YES >> GO TO 9.

P0705 Nissan Altima

NO >> Repair or replace malfunctioning parts.

9.CHECK P POSITION SW CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.
  2. Turn ignition switch ON.
  3. Check voltage between TCM harness connector terminal and ground.

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

10.CHECK L POSITION SWITCH CIRCUIT (PART 1)

  1. Turn ignition switch OFF.
  2. Disconnect TCM connector.
  3. Check continuity between TCM harness connector terminals.

Is the check result normal? YES >> GO TO 11.

NO >> Repair or replace malfunctioning parts.

11.CHECK L POSITION SWITCH CIRCUIT (PART 2)

  1. Disconnect transmission range switch connector.
  2. Turn ignition switch ON.
  3. Check voltage between TCM harness connector terminal and ground.

Is the check result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

12.CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to TM-165, 'Component Inspection'.

Is the check result normal? YES >> Check intermittent incident. Refer to GI-39, 'Intermittent Incident'.

NO >> Repair or replace malfunctioning parts.

Component Inspection

1.CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.


Is the inspection result normal? YES >> INSPECTION END

NO >> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to TM- 283, 'Removal and Installation'.

P062F Eeprom
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P062F EEPROM (Internal Control Module EE ...
P0706 Transmission range sensor A
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0706 T/M RANGE SENSOR A (Transmission R ...
Other materials:

Precaution
Precaution for Supplemental Restraint System (SRS) 'AIR BAG' and 'SEAT BELT PRE-TENSIONER' The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of inju ...

Dtc/circuit diagnosis
Sport mode switch Component function check 1. Check sport mode switch operation Turn ignition switch on. Check sport mode indicator lamp turns on/off on combination meter when turn sport mode switch on/off. Is the inspection result normal? Yes >> inspection end. No >> ...

Removal and installation
EXHAUST SYSTEM Exploded View Sub muffler Spring Mounting rubber Seal bearing Catalyst shroud (upper) Seal bearing Exhaust front tube Spring Catalyst shroud (lower) Clamp Heated oxygen sensor 2 Ring gasket Mounting rubber Main muffler Exhaust finisher (if equipped ...

P0705 Nissan

P0705 Nissan Versa 2014

© 2014-2021 Copyright www.nisentra.com